Black Eagle Archery Front Of Center Outsert System F.O.C.O.S - 12 Pack
€5.20
Preis bei Onlinekauf
Kostenloser Versand
30 Tage kostenlose Rückgabe
Verkauft und versendet von copisteriaunio.egardata.net
Wir bemühen uns, Ihnen genaue Produktinformationen anzuzeigen. Hersteller, Lieferanten und andere stellen die hier gezeigten Angaben bereit.
€5.20
Preis bei Onlinekauf
Kostenloser Versand
30 Tage kostenlose Rückgabe
Verkauft und versendet von copisteriaunio.egardata.net
30 Tage kostenlose Rückgabe Details
Produktdetails
| Artikelnummer | 236471277 | Erscheinungsdatum | 2026/07/09 | Listenpreis | €5.20 | Modellnummer | 236471277 | ||
|---|---|---|---|---|---|---|---|---|---|
| Kategorie | |||||||||
QTY IS 1 DOZEN:
Our New Front Of Center Outsert System is designed for those that want more weight upfront and ease of use of Outserts. The F.O.C.O.S is made of 3 parts. One is the black anodized 7075 T6 aluminum alloy outsert or Stainless Steel Option. Two is a Stainless steel Retention post In The Aluminum Outserts Model and Aluminum in the Stainless Steel Outsert Model that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the Outserts to either be screwed or screwed and glued.(Not Tattooed) This system has been tested to over 550 Pounds per square inch of pull and they stay on! If you are looking for maximum penetration, Maximum F.O.C and shot after shot performance then the deadly combination of the Deep Impact, Instinct or X-Impact shafts then the F.O.C.O.S are sure to be a hit!
Our New Front Of Center Outsert System is designed for those that want more weight upfront and ease of use of Outserts. The F.O.C.O.S is made of 3 parts. One is the black anodized 7075 T6 aluminum alloy outsert or Stainless Steel Option. Two is a Stainless steel Retention post In The Aluminum Outserts Model and Aluminum in the Stainless Steel Outsert Model that also acts as a footer inside the shaft. The third part is the 3/32 allen head retention screw that allows for the Outserts to either be screwed or screwed and glued.(Not Tattooed) This system has been tested to over 550 Pounds per square inch of pull and they stay on! If you are looking for maximum penetration, Maximum F.O.C and shot after shot performance then the deadly combination of the Deep Impact, Instinct or X-Impact shafts then the F.O.C.O.S are sure to be a hit!
INCLUDES:
12 FOCOS OUTSERTS
12 FOCOS POSTS
12 FOCOS Retention Screws
12 FOCOS Retention Screws
Insertion Depth of Arrow in Outsert is .610 almost 5/8"
Outsert adds Approximately 1.090" to end of the Arrow
The Deep Impact & X-Impact Outsert Weights are a Follows:
ALUMINUM OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 80 Grains
STAINLESS STEEL OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 100 Grains
ALUMINUM OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 80 Grains
STAINLESS STEEL OUTSERTS TOTAL WEIGHT
ALL SPINES WEIGH 100 Grains
- To install the F.O.C.O.S System
- Select the right outsert for the right shaft.
- Glue in Stainless steel retention Post
- Dry fitting is recommended on all components. Slide Outserts over shaft and spin test (if you prefer)
- If Outserts does not fit that is OK. Get some 100 Grit sand paper and lightly sand the shaft in a circular motion until the outsert fits fairly snug on shaft. Start slowly so you don't remove to much off the arrow.
- You should have approximately 3/4 of an inch insertion on Aluminum Outserts
- Wipe dust off of the shaft with Clean paper towel. (No Cleaners are recommended)
- Again, Spin test to ensure concentricity.
- Use a Silver or Black Sharpie and mark the Shaft and the Outsert for perfect alignment
- Slide outsert over shaft and use the 3/32 Head retention Screw and Lock the Outsert in place!
- If using glue See steps 11-15 .
- We have tested Our fletching glue, insert/outsert glue and epoxy and all of them work great.
- Apply a even amount of glue around the shaft to ensure you get enough glue in them to hold.
- Slide Outsert On shaft rotating to make sure Glue/Epoxy is evenly dispersed
- Use the 3/32 Head retention Screw and Lock the Outsert in place!
- Once The outsert is glued on Screw is installed stand the arrow on the nock end to dry.
Korrektur der Produktinformationen
Wenn Sie Unvollständigkeiten oder Fehler in den Produktinformationen auf dieser Seite bemerken, nutzen Sie bitte das Korrekturformular unten.
Korrekturanfrage